Dynobike is a combined inertial/braked dynamometer developed for testing power of bikes. This computerized diagnostic system is crucial to deeply monitor performance details of road and race motorbikes.
Thanks to the big roller and the extraordinary efficiency of the eddy current brake (80 kg*m) this combined dyno allows to assess with extreme accuracy and repeatability performance of bikes starting from a few horse power up to the great power of superbikes (theoretical braking power over 500 Hp at 6500 RPM). Its ability to stabilize engine at a certain preset RPM/speed makes it easier to carry out a precise engine tuning through the measuring or diagnostic tools available from the workshop’s equipment.
Dynobike is developed to adapt to any load condition with maximum weight of 1000 kg. Furthermore, it is not very high from the floor, which means that it can be easily accessed with a ramp only 140 cm long so being able to be installed in narrow spaces too, while however being able to test motorbikes up to 2100 mm. Safety equipment preserves personal security by leaving maximum freedom for the operative and actual work. The blocking vise can be finely adjusted to optimize the positioning of the bike at the center of the roller. The forced ventilation system at medium pressure works through a tangential fan of 5.5 kW or 7.5 kW, that can be also linked to an inverter: this allows to supply the right airflow and air speed for engine cooling and the right pressurization of Air Boxes.
The managing software can analyze acquired data in a customized way and can compare up to 8 tests. The user can even decide to assess the power loss in order to calculate the engine power, but also to acquire data at wheel, in a continuous cycle with automatic saving procedure of tests and rapid slowing down. Furthermore, several optional specific sensors allow to acquire data such as: environmental pressure/temperature, engine water/oil temperature, exhaust gas temperature, air/fuel ratio through wideband.
A user-friendly software and no hardware allow to work with a notebook.
Measured values can be assessed thanks to both the digital displays and the graph. By moving the cursor on the chart, the related value is automatically displayed.
Included in the DynoBike, the DYNOTUNE device allows to make self-remapping of Dimsport’s RapidBike add-on modules directly with the software.
|DFMTF TECHNICAL SPECIFICATIONS|
|MAX POWER AT WHEEL||400 KW|
|MAX SPEED||376 KM/H|
|MAX TORQUE AT WHEEL||800 NM|
|DIAMETER OF ROLLER||400 MM|
|WHEELBASE||1200 / 2100 MM|
|MAX LOAD||1000 KG|
|VARIABLE SPEED OF FAN||Α (OPT)|
|ABSORBED ELECTRICAL POWER||2.2 KW|
|DYNO DIMENSIONS TO BE INSTALLED IN THE FLOOR||650 * 395 * 1670 MM|
|DYNO DIMENSIONS TO BE INSTALLED ON THE FLOOR (RAMP INCLUDED)||4200 * 395 * 1670 MM|
|DYNO WEIGHT TO BE INSTALLED IN THE FLOOR (MODULE ONLY)||320 KG|
|DYNO WEIGHT TO BE INSTALLED ON THE FLOOR (RAMP INCLUDED)||570 KG|
|TECHNICAL SPECIFICATIONS OF FAN|
|ELECTRICAL POWER||4 KW||5.5 KW||7.5 KW|
|POWER SUPPLY VOLTAGE||230/400 VAC 50HZ||230/400 VAC 50HZ||230/400 VAC 50HZ|
|AIR SPEED||90 KM/H||200 KM/H||260 KM/H|
|AVERAGE AIR PRESSURE||2.9 MBAR||75 MBAR||85 MBAR|
|AIRFLOW RATE||17000 M³H||1800 M³H||2100 M³H|
|DIMENSION||1200 * 800 * 1400 MM||780 * 465 * 895 MM||780 * 465 * 895 MM|
|INVERTER MANAGEMENT||Α (OPT)||Α (OPT)||Α (OPT)|
|WEIGHT||165 KG||140 KG||175 KG|
|DATA ACQUISITION KIT|
|OIL TEMPERATURE SENSOR (°C) / H2O (°C)||0 – 150 ºC|
|SENSOR OF EXHAUST GAS TEMPERATURE (K)||0 – 1.000 ºC|
|BOOST PRESSURE SENSOR (BAR)||-1.00 + 3.00|
|OXYGEN SENSOR WIDE BAND||0 – 5 VCC|
|SENSOR OF INTAKE AIR TEMPERATURE||-10 – + 60 ºC|
Measurement data are collected and standardized through an integrated barometric unit in accordance with the following regulations: DIN 70020, EGW 80/1269, ISO 1585, SAE J1349, JIS D1001